LISTSERV at the University of Georgia
Menubar Imagemap
Home Browse Manage Request Manuals Register
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2002, week 2)Back to main SAS-L pageJoin or leave SAS-L (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Wed, 10 Apr 2002 12:22:59 -0700
Reply-To:   "William W. Viergever" <wwvierg@ATTGLOBAL.NET>
Sender:   "SAS(r) Discussion" <SAS-L@LISTSERV.UGA.EDU>
From:   "William W. Viergever" <wwvierg@ATTGLOBAL.NET>
Subject:   Re: Corrupted files
Comments:   To: Pamela Nadash <PNadash@VNSNY.ORG>
In-Reply-To:   <A5C7EAD93596D411B41500D0B7B96447851143@xcgism0104.vnsny.or g>
Content-Type:   text/plain; charset="us-ascii"; format=flowed

Don't bother re-installing SAS; instead re-create the data sets.

They're hosed.

You may, in fact, wish to check out the other files on this drive; back-up the good ones and then re-format (i.e., start w/ a low level, device format which will block-out bad sectors/tracks) this drive; I suspect it is beginning to die as I recently had the same experience w/ a 36GB U160 SCSI drive.

All this assumes you have more than just C; otherwise you might be re-installing everything <g>

HTH

At 03:09 PM 4/10/2002 -0400, Pamela Nadash wrote: >Seemingly randomly, I am getting errors using my SAS permanent datasets, as >follows: > >82 data vcpage; >83 set c.vcp_set2 (keep=mrn case_num age); >84 run; > >ERROR: Expecting page 546, got page -1 instead. >ERROR: Page validation error while reading C.VCP_SET2.DATA. >ERROR: File C.VCP_SET2.DATA is damaged. I/O processing did not complete. >NOTE: The data step has been abnormally terminated. >NOTE: The SAS System stopped processing this step because of errors. >NOTE: There were 2711 observations read from the data set C.VCP_SET2. >WARNING: The data set WORK.VCPAGE may be incomplete. When this step was >stopped there were 2711 observations and 3 > variables. >NOTE: DATA statement used: > real time 1.47 seconds > cpu time 0.15 seconds > >then for another file: > > >14 data full; >15 set c.vcp_full; >16 if age > 64 then output; >17 run; > >ERROR: Expecting page 51, got page -1 instead. >ERROR: Page validation error while reading C.VCP_FULL.DATA. >ERROR: File C.VCP_FULL.DATA is damaged. I/O processing did not complete. > >The source files were modified at different points in time -- one over 2 >months ago. I have been getting this error a few times over the last few >days. The computer has been checked out, and there seem to be no viruses or >other problems. My next step is to re-install SAS, but I would be grateful >for any insight into what might have caused this error. > > Pamela Nadash > Research Associate > Center for Home Care Policy and Research > The Visiting Nurse Service of NY > 5 Penn Plaza, 11th Floor > New York, NY 10001-1810 > > Tel: 212/290-3537 Fax: 212/290-3756

------------------------------------------------------------ William W. Viergever Voice : (916) 483-8398 Viergever & Associates Fax : (916) 486-1488 Sacramento, CA 95825 E-mail : wwvierg@attglobal.net ------------------------------------------------------------


Back to: Top of message | Previous page | Main SAS-L page